PreCONNECT® OCTO MTP® Breakout Trunk cable Applications MTP® (MPO) based data center cabling with 8 fibers per MTP® channel. Optimized for parallel optics MPO 4+4 fiber applications: 40/100/200 GBASE-SR4 400GBASE-SR4.2 BiDi 4x16, 4x32 and 4x64 GFC 100GBASE DR4/PSM4 200GBASE-DR4 400GBASE-DR4 4x10 GBASE-LR Easy migration to higher speed applications. More information about the different applications can be found in the product information or in the product profile under Data sheets. Properties PreCONNECT® OCTO Breakout Trunk cables with I-F(ZN)HH breakout cables: Breakout trunk cable have PreCONNECT® square-interfaces on both sides which can be tool-less hooked into the 19” panel systems for tensile and torsion resistant fixing of the trunk cables. Installation protection: The trunk connector legs are fitting for the 19“ panel systems and are packed in non-pull resistant dust-proof foil tubes. On request with tensile strength, crush resistant, kink and torsion resistant, installation tubes deliverable. Connector type: OCTO Trunk cables: MTP® OCTO 4+4 fiber male Polarity: OCTO Trunk cables: TIA Method B „1 to 12“ Fiber types: Multimode OM4 bend-insensitive Singlemode G.657.A1 bend-insensitive and backwards compatible to G.652.D Length definition: Order-length = length between the connectors of the longest legs at both sides, not between the PreCONNECT® square-interfaces. Scope of delivery and packaging: Dependent on the length as cable ring or on cardboard or wooden drum Insertion loss and return loss measured acc. to IEC 61300-3-4, method B, MM 850/1300nm and SM 1310/1550nm, with measurement protocol Product label with serial number at both sides Benefits MTP® cabling system perfectly fitting for SR4 and DR4/PSM4 applications Cost reduction through the only for SR4 and DR4/PSM4 needed 8 fibers instead of the so far usual 12 are in one MTP® channel Fast and safe installation trough factory assembled plug & play systematic Highest quality and cost-efficiency through factory assembling PreCONNECT® cabling systems consist of perfectly harmonized modular single components

PreCONNECT® OCTO MTP® Breakout Trunk cable Applications MTP® (MPO) based data center cabling with 8 fibers per MTP® channel. Optimized for parallel optics MPO 4+4 fiber applications: 40/100/200 GBASE-SR4 400GBASE-SR4.2 BiDi 4x16, 4x32 and 4x64 GFC 100GBASE DR4/PSM4 200GBASE-DR4 400GBASE-DR4 4x10 GBASE-LR Easy migration to higher speed applications. More information about the different applications can be found in the product information or in the product profile under Data sheets. Properties PreCONNECT® OCTO Breakout Trunk cables with I-F(ZN)HH breakout cables: Breakout trunk cable have PreCONNECT® square-interfaces on both sides which can be tool-less hooked into the 19” panel systems for tensile and torsion resistant fixing of the trunk cables. Installation protection: The trunk connector legs are fitting for the 19“ panel systems and are packed in non-pull resistant dust-proof foil tubes. On request with tensile strength, crush resistant, kink and torsion resistant, installation tubes deliverable. Connector type: OCTO Trunk cables: MTP® OCTO 4+4 fiber male Polarity: OCTO Trunk cables: TIA Method B „1 to 12“ Fiber types: Multimode OM4 bend-insensitive Singlemode G.657.A1 bend-insensitive and backwards compatible to G.652.D Length definition: Order-length = length between the connectors of the longest legs at both sides, not between the PreCONNECT® square-interfaces. Scope of delivery and packaging: Dependent on the length as cable ring or on cardboard or wooden drum Insertion loss and return loss measured acc. to IEC 61300-3-4, method B, MM 850/1300nm and SM 1310/1550nm, with measurement protocol Product label with serial number at both sides Benefits MTP® cabling system perfectly fitting for SR4 and DR4/PSM4 applications Cost reduction through the only for SR4 and DR4/PSM4 needed 8 fibers instead of the so far usual 12 are in one MTP® channel Fast and safe installation trough factory assembled plug & play systematic Highest quality and cost-efficiency through factory assembling PreCONNECT® cabling systems consist of perfectly harmonized modular single components

PreCONNECT® OCTO MTP® Breakout Trunk cable Applications MTP® (MPO) based data center cabling with 8 fibers per MTP® channel. Optimized for parallel optics MPO 4+4 fiber applications: 40/100/200 GBASE-SR4 400GBASE-SR4.2 BiDi 4x16, 4x32 and 4x64 GFC 100GBASE DR4/PSM4 200GBASE-DR4 400GBASE-DR4 4x10 GBASE-LR Easy migration to higher speed applications. More information about the different applications can be found in the product information or in the product profile under Data sheets. Properties PreCONNECT® OCTO Breakout Trunk cables with I-F(ZN)HH breakout cables: Breakout trunk cable have PreCONNECT® square-interfaces on both sides which can be tool-less hooked into the 19” panel systems for tensile and torsion resistant fixing of the trunk cables. Installation protection: The trunk connector legs are fitting for the 19“ panel systems and are packed in non-pull resistant dust-proof foil tubes. On request with tensile strength, crush resistant, kink and torsion resistant, installation tubes deliverable. Connector type: OCTO Trunk cables: MTP® OCTO 4+4 fiber male Polarity: OCTO Trunk cables: TIA Method B „1 to 12“ Fiber types: Multimode OM4 bend-insensitive Singlemode G.657.A1 bend-insensitive and backwards compatible to G.652.D Length definition: Order-length = length between the connectors of the longest legs at both sides, not between the PreCONNECT® square-interfaces. Scope of delivery and packaging: Dependent on the length as cable ring or on cardboard or wooden drum Insertion loss and return loss measured acc. to IEC 61300-3-4, method B, MM 850/1300nm and SM 1310/1550nm, with measurement protocol Product label with serial number at both sides Benefits MTP® cabling system perfectly fitting for SR4 and DR4/PSM4 applications Cost reduction through the only for SR4 and DR4/PSM4 needed 8 fibers instead of the so far usual 12 are in one MTP® channel Fast and safe installation trough factory assembled plug & play systematic Highest quality and cost-efficiency through factory assembling PreCONNECT® cabling systems consist of perfectly harmonized modular single components

PreCONNECT® OCTO MTP® Breakout Trunk cable Applications MTP® (MPO) based data center cabling with 8 fibers per MTP® channel. Optimized for parallel optics MPO 4+4 fiber applications: 40/100/200 GBASE-SR4 400GBASE-SR4.2 BiDi 4x16, 4x32 and 4x64 GFC 100GBASE DR4/PSM4 200GBASE-DR4 400GBASE-DR4 4x10 GBASE-LR Easy migration to higher speed applications. More information about the different applications can be found in the product information or in the product profile under Data sheets. Properties PreCONNECT® OCTO Breakout Trunk cables with I-F(ZN)HH breakout cables: Breakout trunk cable have PreCONNECT® square-interfaces on both sides which can be tool-less hooked into the 19” panel systems for tensile and torsion resistant fixing of the trunk cables. Installation protection: The trunk connector legs are fitting for the 19“ panel systems and are packed in non-pull resistant dust-proof foil tubes. On request with tensile strength, crush resistant, kink and torsion resistant, installation tubes deliverable. Connector type: OCTO Trunk cables: MTP® OCTO 4+4 fiber male Polarity: OCTO Trunk cables: TIA Method B „1 to 12“ Fiber types: Multimode OM4 bend-insensitive Singlemode G.657.A1 bend-insensitive and backwards compatible to G.652.D Length definition: Order-length = length between the connectors of the longest legs at both sides, not between the PreCONNECT® square-interfaces. Scope of delivery and packaging: Dependent on the length as cable ring or on cardboard or wooden drum Insertion loss and return loss measured acc. to IEC 61300-3-4, method B, MM 850/1300nm and SM 1310/1550nm, with measurement protocol Product label with serial number at both sides Benefits MTP® cabling system perfectly fitting for SR4 and DR4/PSM4 applications Cost reduction through the only for SR4 and DR4/PSM4 needed 8 fibers instead of the so far usual 12 are in one MTP® channel Fast and safe installation trough factory assembled plug & play systematic Highest quality and cost-efficiency through factory assembling PreCONNECT® cabling systems consist of perfectly harmonized modular single components

PreCONNECT® BREAKOUT Applications Data centers and their IT rooms, data center containers and EDGE computing sites. Universal to use fiber optic cabling system up to 24 fibers per trunk Cost and attenuation optimized Focused on a practical and necessary approach We see breakout trunk cables for short lengths and up to 24 fibers as an alternative product to our proven loose tube cable-based trunk cables with distribution heads. Breakout trunk cables do not require distribution heads, since the connectors are directly assembled on the robust sub-elements of the breakout cables. More information about the different applications can be found in separates product information. Properties PreCONNECT® BREAKOUT Trunk cable: Breakout trunk cable have PreCONNECT® square-interfaces on both sides which can be tool-less hooked into the 19” panel systems for tensile and torsion resistant fixing of the trunk cables. Cable ends can be assembled with „variable“ long or "stepped" connector legs. Installation protection: The connector legs are packed in a non pull resistant dustproof foil tube. Stepped connector legs can be packed optionally in indoor IP50 dustproof, 150 N tensile, step and kink resistant, installation tubes. Connector types: According to IEC 61754-x, for more connector specifications see data sheet. MTP®: IEC 61754-7 LC: IEC 61754-20 Polarity: The connector legs are alphanumerically uniquely coded. The standard polarity is „channel-wise crossed“ (pairwise flipped) for full-duplex transmission systems – A1 to B1, A2 to B2, etc. On request „uncrossed“ deliverable. Fiber types: According to ISO/IEC 11801, EN 50173-1, IEC 60793-2-x and ITUG65x, for more fiber specifications see data sheet. OM3: IEC 60793-2-10 type A1a.2, ITU G.651.1 OM4: IEC 60793-2-10 type A1a.3, ITU G.651.1 OM5: IEC 60793-2-10 type A1a.4, ITU G.651.1 OS2: IEC 60793-2-50 type B1.3, ITU G.657.A1 Cable type: FRNC-LSZH cable, for more cable specifications see data sheet. Length definition: Order-length = length between the connectors of the longest legs at both sides, not between the PreCONNECT® cable dividers. Scope of delivery and packaging: Dependent on the length as cable ring or on cardboard or wooden drum, 100% IL factory measured with measurement protocol, measurement values on request or via our website: https://www.rosenberger.com/en/downloads/mdm.php. Serial number on both cable ends for network documentation, Product ID label on each packaging, including installation manual, available in any standard length. Benefits Most cost-effective solution for trunks up to 24 fibers and short lengths Fast and safe installation trough factory assembled Plug & Play systematic Highest quality and cost-efficiency through factory assembling PreCONNECT® cabling systems consist of perfectly harmonized modular single components.

PreCONNECT® OCTO MTP® Breakout Trunk cable Applications MTP® (MPO) based data center cabling with 8 fibers per MTP® channel. Optimized for parallel optics MPO 4+4 fiber applications: 40/100/200 GBASE-SR4 400GBASE-SR4.2 BiDi 4x16, 4x32 and 4x64 GFC 100GBASE DR4/PSM4 200GBASE-DR4 400GBASE-DR4 4x10 GBASE-LR Easy migration to higher speed applications. More information about the different applications can be found in the product information or in the product profile under Data sheets. Properties PreCONNECT® OCTO Breakout Trunk cables with I-F(ZN)HH breakout cables: Breakout trunk cable have PreCONNECT® square-interfaces on both sides which can be tool-less hooked into the 19” panel systems for tensile and torsion resistant fixing of the trunk cables. Installation protection: The trunk connector legs are fitting for the 19“ panel systems and are packed in non-pull resistant dust-proof foil tubes. On request with tensile strength, crush resistant, kink and torsion resistant, installation tubes deliverable. Connector type: OCTO Trunk cables: MTP® OCTO 4+4 fiber male Polarity: OCTO Trunk cables: TIA Method B „1 to 12“ Fiber types: Multimode OM4 bend-insensitive Singlemode G.657.A1 bend-insensitive and backwards compatible to G.652.D Length definition: Order-length = length between the connectors of the longest legs at both sides, not between the PreCONNECT® square-interfaces. Scope of delivery and packaging: Dependent on the length as cable ring or on cardboard or wooden drum Insertion loss and return loss measured acc. to IEC 61300-3-4, method B, MM 850/1300nm and SM 1310/1550nm, with measurement protocol Product label with serial number at both sides Benefits MTP® cabling system perfectly fitting for SR4 and DR4/PSM4 applications Cost reduction through the only for SR4 and DR4/PSM4 needed 8 fibers instead of the so far usual 12 are in one MTP® channel Fast and safe installation trough factory assembled plug & play systematic Highest quality and cost-efficiency through factory assembling PreCONNECT® cabling systems consist of perfectly harmonized modular single components

PreCONNECT® BREAKOUT Applications Data centers and their IT rooms, data center containers and EDGE computing sites. Universal to use fiber optic cabling system up to 24 fibers per trunk Cost and attenuation optimized Focused on a practical and necessary approach We see breakout trunk cables for short lengths and up to 24 fibers as an alternative product to our proven loose tube cable-based trunk cables with distribution heads. Breakout trunk cables do not require distribution heads, since the connectors are directly assembled on the robust sub-elements of the breakout cables. More information about the different applications can be found in separates product information. Properties PreCONNECT® BREAKOUT Trunk cable: Breakout trunk cable have PreCONNECT® square-interfaces on both sides which can be tool-less hooked into the 19” panel systems for tensile and torsion resistant fixing of the trunk cables. Cable ends can be assembled with „variable“ long or "stepped" connector legs. Installation protection: The connector legs are packed in a non pull resistant dustproof foil tube. Stepped connector legs can be packed optionally in indoor IP50 dustproof, 150 N tensile, step and kink resistant, installation tubes. Connector types: According to IEC 61754-x, for more connector specifications see data sheet. MTP®: IEC 61754-7 LC: IEC 61754-20 Polarity: The connector legs are alphanumerically uniquely coded. The standard polarity is „channel-wise crossed“ (pairwise flipped) for full-duplex transmission systems – A1 to B1, A2 to B2, etc. On request „uncrossed“ deliverable. Fiber types: According to ISO/IEC 11801, EN 50173-1, IEC 60793-2-x and ITUG65x, for more fiber specifications see data sheet. OM3: IEC 60793-2-10 type A1a.2, ITU G.651.1 OM4: IEC 60793-2-10 type A1a.3, ITU G.651.1 OM5: IEC 60793-2-10 type A1a.4, ITU G.651.1 OS2: IEC 60793-2-50 type B1.3, ITU G.657.A1 Cable type: FRNC-LSZH cable, for more cable specifications see data sheet. Length definition: Order-length = length between the connectors of the longest legs at both sides, not between the PreCONNECT® cable dividers. Scope of delivery and packaging: Dependent on the length as cable ring or on cardboard or wooden drum, 100% IL factory measured with measurement protocol, measurement values on request or via our website: https://www.rosenberger.com/en/downloads/mdm.php. Serial number on both cable ends for network documentation, Product ID label on each packaging, including installation manual, available in any standard length. Benefits Most cost-effective solution for trunks up to 24 fibers and short lengths Fast and safe installation trough factory assembled Plug & Play systematic Highest quality and cost-efficiency through factory assembling PreCONNECT® cabling systems consist of perfectly harmonized modular single components.

PreCONNECT® OCTO MTP® Breakout Trunk cable Applications MTP® (MPO) based data center cabling with 8 fibers per MTP® channel. Optimized for parallel optics MPO 4+4 fiber applications: 40/100/200 GBASE-SR4 400GBASE-SR4.2 BiDi 4x16, 4x32 and 4x64 GFC 100GBASE DR4/PSM4 200GBASE-DR4 400GBASE-DR4 4x10 GBASE-LR Easy migration to higher speed applications. More information about the different applications can be found in the product information or in the product profile under Data sheets. Properties PreCONNECT® OCTO Breakout Trunk cables with I-F(ZN)HH breakout cables: Breakout trunk cable have PreCONNECT® square-interfaces on both sides which can be tool-less hooked into the 19” panel systems for tensile and torsion resistant fixing of the trunk cables. Installation protection: The trunk connector legs are fitting for the 19“ panel systems and are packed in non-pull resistant dust-proof foil tubes. On request with tensile strength, crush resistant, kink and torsion resistant, installation tubes deliverable. Connector type: OCTO Trunk cables: MTP® OCTO 4+4 fiber male Polarity: OCTO Trunk cables: TIA Method B „1 to 12“ Fiber types: Multimode OM4 bend-insensitive Singlemode G.657.A1 bend-insensitive and backwards compatible to G.652.D Length definition: Order-length = length between the connectors of the longest legs at both sides, not between the PreCONNECT® square-interfaces. Scope of delivery and packaging: Dependent on the length as cable ring or on cardboard or wooden drum Insertion loss and return loss measured acc. to IEC 61300-3-4, method B, MM 850/1300nm and SM 1310/1550nm, with measurement protocol Product label with serial number at both sides Benefits MTP® cabling system perfectly fitting for SR4 and DR4/PSM4 applications Cost reduction through the only for SR4 and DR4/PSM4 needed 8 fibers instead of the so far usual 12 are in one MTP® channel Fast and safe installation trough factory assembled plug & play systematic Highest quality and cost-efficiency through factory assembling PreCONNECT® cabling systems consist of perfectly harmonized modular single components

PreCONNECT® OCTO MTP® Breakout Trunk cable Applications MTP® (MPO) based data center cabling with 8 fibers per MTP® channel. Optimized for parallel optics MPO 4+4 fiber applications: 40/100/200 GBASE-SR4 400GBASE-SR4.2 BiDi 4x16, 4x32 and 4x64 GFC 100GBASE DR4/PSM4 200GBASE-DR4 400GBASE-DR4 4x10 GBASE-LR Easy migration to higher speed applications. More information about the different applications can be found in the product information or in the product profile under Data sheets. Properties PreCONNECT® OCTO Breakout Trunk cables with I-F(ZN)HH breakout cables: Breakout trunk cable have PreCONNECT® square-interfaces on both sides which can be tool-less hooked into the 19” panel systems for tensile and torsion resistant fixing of the trunk cables. Installation protection: The trunk connector legs are fitting for the 19“ panel systems and are packed in non-pull resistant dust-proof foil tubes. On request with tensile strength, crush resistant, kink and torsion resistant, installation tubes deliverable. Connector type: OCTO Trunk cables: MTP® OCTO 4+4 fiber male Polarity: OCTO Trunk cables: TIA Method B „1 to 12“ Fiber types: Multimode OM4 bend-insensitive Singlemode G.657.A1 bend-insensitive and backwards compatible to G.652.D Length definition: Order-length = length between the connectors of the longest legs at both sides, not between the PreCONNECT® square-interfaces. Scope of delivery and packaging: Dependent on the length as cable ring or on cardboard or wooden drum Insertion loss and return loss measured acc. to IEC 61300-3-4, method B, MM 850/1300nm and SM 1310/1550nm, with measurement protocol Product label with serial number at both sides Benefits MTP® cabling system perfectly fitting for SR4 and DR4/PSM4 applications Cost reduction through the only for SR4 and DR4/PSM4 needed 8 fibers instead of the so far usual 12 are in one MTP® channel Fast and safe installation trough factory assembled plug & play systematic Highest quality and cost-efficiency through factory assembling PreCONNECT® cabling systems consist of perfectly harmonized modular single components

PreCONNECT® OCTO MTP® Breakout Trunk cable Applications MTP® (MPO) based data center cabling with 8 fibers per MTP® channel. Optimized for parallel optics MPO 4+4 fiber applications: 40/100/200 GBASE-SR4 400GBASE-SR4.2 BiDi 4x16, 4x32 and 4x64 GFC 100GBASE DR4/PSM4 200GBASE-DR4 400GBASE-DR4 4x10 GBASE-LR Easy migration to higher speed applications. More information about the different applications can be found in the product information or in the product profile under Data sheets. Properties PreCONNECT® OCTO Breakout Trunk cables with I-F(ZN)HH breakout cables: Breakout trunk cable have PreCONNECT® square-interfaces on both sides which can be tool-less hooked into the 19” panel systems for tensile and torsion resistant fixing of the trunk cables. Installation protection: The trunk connector legs are fitting for the 19“ panel systems and are packed in non-pull resistant dust-proof foil tubes. On request with tensile strength, crush resistant, kink and torsion resistant, installation tubes deliverable. Connector type: OCTO Trunk cables: MTP® OCTO 4+4 fiber male Polarity: OCTO Trunk cables: TIA Method B „1 to 12“ Fiber types: Multimode OM4 bend-insensitive Singlemode G.657.A1 bend-insensitive and backwards compatible to G.652.D Length definition: Order-length = length between the connectors of the longest legs at both sides, not between the PreCONNECT® square-interfaces. Scope of delivery and packaging: Dependent on the length as cable ring or on cardboard or wooden drum Insertion loss and return loss measured acc. to IEC 61300-3-4, method B, MM 850/1300nm and SM 1310/1550nm, with measurement protocol Product label with serial number at both sides Benefits MTP® cabling system perfectly fitting for SR4 and DR4/PSM4 applications Cost reduction through the only for SR4 and DR4/PSM4 needed 8 fibers instead of the so far usual 12 are in one MTP® channel Fast and safe installation trough factory assembled plug & play systematic Highest quality and cost-efficiency through factory assembling PreCONNECT® cabling systems consist of perfectly harmonized modular single components

PreCONNECT® TRUNK MULTIJUMPERApplicationsCabling of large switches and floor-standing IT hardware within data centers, to represent their ports in a patch location.Trunk Multijumper up to 144 fibers per trunkCost and attenuation optimizedFocused on a practical and necessary approachMore information about the different applications can be found in the separates product information.PropertiesPreCONNECT® MULTIJUMPER Trunk cable:Cable ends are molded in distribution heads and assembled with „variable“ long or "stepped" connector legs.The PreCONNECT® cable divider is a mechanically and thermally robust and splice-less cable divider for fiber separation of loose tube cables. With its integrated PreCONNECT® square interface, the cable divider can be tool-less hooked into PreCONNECT® panels for tensile and torsion resistant fixing of the trunk cables.Installation protection:The connector legs and cable dividers are packed in with a non pull resistant dustproof foil tube. Stepped connector legs can be packed optionally in 600 N tensile strength, crush resistant, kink and torsion resistant, installation tubes.Connector types:According to IEC 61754-x, for more connector specifications see data sheet.SC: IEC 61754-4MTP®: IEC 61754-7E2000®: IEC 61754-15LC: IEC 61754-20Polarity:The connector legs are alphanumerically uniquely coded. The standard polarity is „channel-wise crossed“ (pairwise flipped) for full-duplex transmission systems – A1 to B1, A2 to B2, etc. On request „uncrossed“ deliverable.Fiber types:According to ISO/IEC 11801, EN 50173-1, IEC 60793-2-x and ITUG65x, for more fiber specifications see data sheet.OM3: IEC 60793-2-10 type A1a.2, ITU G.651.1OM4: IEC 60793-2-10 type A1a.3, ITU G.651.1OM5: IEC 60793-2-10 type A1a.4, ITU G.651.1OS2: IEC 60793-2-50 type B1.3, ITU G.657.A1Cable type:FRNC-LSZH cable, for more cable specifications see data sheet.Length definition:Order-length = length between the connectors of the longest legs at both sides, not between the PreCONNECT® cable dividers.Scope of delivery and packaging:Dependent on the length as cable ring or on cardboard or wooden drum, 100% IL factory measured with measurement protocol, measurement values on request or via our website: https://www.rosenberger.com/en/downloads/mdm.php. Serial number on both sides of cable ends for network documentation, Product ID label on each packaging, including installation manual available in any standard length.BenefitsCost reduction through direct attach of the IT Hardware Transceivers to the TMJ connector legsMost cost-effective solution for trunks up to 24 fibers and short lengthsAttenuation reduction through the saving of one connection in the transmission channelApplication specific individually configurableFast and safe installation trough factory assembled Plug & Play systematicHighest quality and cost-efficiency through factory assemblingPreCONNECT® cabling systems consist of perfectly harmonized modular single components.

PreCONNECT® TRUNK MULTIJUMPERApplicationsCabling of large switches and floor-standing IT hardware within data centers, to represent their ports in a patch location.Trunk Multijumper up to 144 fibers per trunkCost and attenuation optimizedFocused on a practical and necessary approachMore information about the different applications can be found in the separates product information.PropertiesPreCONNECT® MULTIJUMPER Trunk cable:Cable ends are molded in distribution heads and assembled with „variable“ long or "stepped" connector legs.The PreCONNECT® cable divider is a mechanically and thermally robust and splice-less cable divider for fiber separation of loose tube cables. With its integrated PreCONNECT® square interface, the cable divider can be tool-less hooked into PreCONNECT® panels for tensile and torsion resistant fixing of the trunk cables.Installation protection:The connector legs and cable dividers are packed in with a non pull resistant dustproof foil tube. Stepped connector legs can be packed optionally in 600 N tensile strength, crush resistant, kink and torsion resistant, installation tubes.Connector types:According to IEC 61754-x, for more connector specifications see data sheet.SC: IEC 61754-4MTP®: IEC 61754-7E2000®: IEC 61754-15LC: IEC 61754-20Polarity:The connector legs are alphanumerically uniquely coded. The standard polarity is „channel-wise crossed“ (pairwise flipped) for full-duplex transmission systems – A1 to B1, A2 to B2, etc. On request „uncrossed“ deliverable.Fiber types:According to ISO/IEC 11801, EN 50173-1, IEC 60793-2-x and ITUG65x, for more fiber specifications see data sheet.OM3: IEC 60793-2-10 type A1a.2, ITU G.651.1OM4: IEC 60793-2-10 type A1a.3, ITU G.651.1OM5: IEC 60793-2-10 type A1a.4, ITU G.651.1OS2: IEC 60793-2-50 type B1.3, ITU G.657.A1Cable type:FRNC-LSZH cable, for more cable specifications see data sheet.Length definition:Order-length = length between the connectors of the longest legs at both sides, not between the PreCONNECT® cable dividers.Scope of delivery and packaging:Dependent on the length as cable ring or on cardboard or wooden drum, 100% IL factory measured with measurement protocol, measurement values on request or via our website: https://www.rosenberger.com/en/downloads/mdm.php. Serial number on both sides of cable ends for network documentation, Product ID label on each packaging, including installation manual available in any standard length.BenefitsCost reduction through direct attach of the IT Hardware Transceivers to the TMJ connector legsMost cost-effective solution for trunks up to 24 fibers and short lengthsAttenuation reduction through the saving of one connection in the transmission channelApplication specific individually configurableFast and safe installation trough factory assembled Plug & Play systematicHighest quality and cost-efficiency through factory assemblingPreCONNECT® cabling systems consist of perfectly harmonized modular single components.

PreCONNECT® TRUNK MULTIJUMPERApplicationsCabling of large switches and floor-standing IT hardware within data centers, to represent their ports in a patch location.Trunk Multijumper up to 144 fibers per trunkCost and attenuation optimizedFocused on a practical and necessary approachMore information about the different applications can be found in the separates product information.PropertiesPreCONNECT® MULTIJUMPER Trunk cable:Cable ends are molded in distribution heads and assembled with „variable“ long or "stepped" connector legs.The PreCONNECT® cable divider is a mechanically and thermally robust and splice-less cable divider for fiber separation of loose tube cables. With its integrated PreCONNECT® square interface, the cable divider can be tool-less hooked into PreCONNECT® panels for tensile and torsion resistant fixing of the trunk cables.Installation protection:The connector legs and cable dividers are packed in with a non pull resistant dustproof foil tube. Stepped connector legs can be packed optionally in 600 N tensile strength, crush resistant, kink and torsion resistant, installation tubes.Connector types:According to IEC 61754-x, for more connector specifications see data sheet.SC: IEC 61754-4MTP®: IEC 61754-7E2000®: IEC 61754-15LC: IEC 61754-20Polarity:The connector legs are alphanumerically uniquely coded. The standard polarity is „channel-wise crossed“ (pairwise flipped) for full-duplex transmission systems – A1 to B1, A2 to B2, etc. On request „uncrossed“ deliverable.Fiber types:According to ISO/IEC 11801, EN 50173-1, IEC 60793-2-x and ITUG65x, for more fiber specifications see data sheet.OM3: IEC 60793-2-10 type A1a.2, ITU G.651.1OM4: IEC 60793-2-10 type A1a.3, ITU G.651.1OM5: IEC 60793-2-10 type A1a.4, ITU G.651.1OS2: IEC 60793-2-50 type B1.3, ITU G.657.A1Cable type:FRNC-LSZH cable, for more cable specifications see data sheet.Length definition:Order-length = length between the connectors of the longest legs at both sides, not between the PreCONNECT® cable dividers.Scope of delivery and packaging:Dependent on the length as cable ring or on cardboard or wooden drum, 100% IL factory measured with measurement protocol, measurement values on request or via our website: https://www.rosenberger.com/en/downloads/mdm.php. Serial number on both sides of cable ends for network documentation, Product ID label on each packaging, including installation manual available in any standard length.BenefitsCost reduction through direct attach of the IT Hardware Transceivers to the TMJ connector legsMost cost-effective solution for trunks up to 24 fibers and short lengthsAttenuation reduction through the saving of one connection in the transmission channelApplication specific individually configurableFast and safe installation trough factory assembled Plug & Play systematicHighest quality and cost-efficiency through factory assemblingPreCONNECT® cabling systems consist of perfectly harmonized modular single components.

PreCONNECT® TRUNK MULTIJUMPERApplicationsCabling of large switches and floor-standing IT hardware within data centers, to represent their ports in a patch location.Trunk Multijumper up to 144 fibers per trunkCost and attenuation optimizedFocused on a practical and necessary approachMore information about the different applications can be found in the separates product information.PropertiesPreCONNECT® MULTIJUMPER Trunk cable:Cable ends are molded in distribution heads and assembled with „variable“ long or "stepped" connector legs.The PreCONNECT® cable divider is a mechanically and thermally robust and splice-less cable divider for fiber separation of loose tube cables. With its integrated PreCONNECT® square interface, the cable divider can be tool-less hooked into PreCONNECT® panels for tensile and torsion resistant fixing of the trunk cables.Installation protection:The connector legs and cable dividers are packed in with a non pull resistant dustproof foil tube. Stepped connector legs can be packed optionally in 600 N tensile strength, crush resistant, kink and torsion resistant, installation tubes.Connector types:According to IEC 61754-x, for more connector specifications see data sheet.SC: IEC 61754-4MTP®: IEC 61754-7E2000®: IEC 61754-15LC: IEC 61754-20Polarity:The connector legs are alphanumerically uniquely coded. The standard polarity is „channel-wise crossed“ (pairwise flipped) for full-duplex transmission systems – A1 to B1, A2 to B2, etc. On request „uncrossed“ deliverable.Fiber types:According to ISO/IEC 11801, EN 50173-1, IEC 60793-2-x and ITUG65x, for more fiber specifications see data sheet.OM3: IEC 60793-2-10 type A1a.2, ITU G.651.1OM4: IEC 60793-2-10 type A1a.3, ITU G.651.1OM5: IEC 60793-2-10 type A1a.4, ITU G.651.1OS2: IEC 60793-2-50 type B1.3, ITU G.657.A1Cable type:FRNC-LSZH cable, for more cable specifications see data sheet.Length definition:Order-length = length between the connectors of the longest legs at both sides, not between the PreCONNECT® cable dividers.Scope of delivery and packaging:Dependent on the length as cable ring or on cardboard or wooden drum, 100% IL factory measured with measurement protocol, measurement values on request or via our website: https://www.rosenberger.com/en/downloads/mdm.php. Serial number on both sides of cable ends for network documentation, Product ID label on each packaging, including installation manual available in any standard length.BenefitsCost reduction through direct attach of the IT Hardware Transceivers to the TMJ connector legsMost cost-effective solution for trunks up to 24 fibers and short lengthsAttenuation reduction through the saving of one connection in the transmission channelApplication specific individually configurableFast and safe installation trough factory assembled Plug & Play systematicHighest quality and cost-efficiency through factory assemblingPreCONNECT® cabling systems consist of perfectly harmonized modular single components.

PreCONNECT® TRUNK MULTIJUMPER Applications Cabling of large switches and floor-standing IT hardware within data centers, to represent their ports in a patch location. Trunk Multijumper up to 144 fibers per trunk Cost and attenuation optimized Focused on a practical and necessary approach More information about the different applications can be found in the separates product information. Properties PreCONNECT® MULTIJUMPER Trunk cable: Cable ends are molded in distribution heads and assembled with „variable“ long or "stepped" connector legs. The PreCONNECT® cable divider is a mechanically and thermally robust and splice-less cable divider for fiber separation of loose tube cables. With its integrated PreCONNECT® square interface, the cable divider can be tool-less hooked into PreCONNECT® panels for tensile and torsion resistant fixing of the trunk cables. Installation protection: The connector legs and cable dividers are packed in with a non pull resistant dustproof foil tube. Stepped connector legs can be packed optionally in 600 N tensile strength, crush resistant, kink and torsion resistant, installation tubes. Connector types: According to IEC 61754-x, for more connector specifications see data sheet. SC: IEC 61754-4 MTP®: IEC 61754-7 E2000®: IEC 61754-15 LC: IEC 61754-20 Polarity: The connector legs are alphanumerically uniquely coded. The standard polarity is „channel-wise crossed“ (pairwise flipped) for full-duplex transmission systems – A1 to B1, A2 to B2, etc. On request „uncrossed“ deliverable. Fiber types: According to ISO/IEC 11801, EN 50173-1, IEC 60793-2-x and ITUG65x, for more fiber specifications see data sheet. OM3: IEC 60793-2-10 type A1a.2, ITU G.651.1 OM4: IEC 60793-2-10 type A1a.3, ITU G.651.1 OM5: IEC 60793-2-10 type A1a.4, ITU G.651.1 OS2: IEC 60793-2-50 type B1.3, ITU G.657.A1 Cable type: FRNC-LSZH cable, for more cable specifications see data sheet. Length definition: Order-length = length between the connectors of the longest legs at both sides, not between the PreCONNECT® cable dividers. Scope of delivery and packaging: Dependent on the length as cable ring or on cardboard or wooden drum, 100% IL factory measured with measurement protocol, measurement values on request or via our website: https://www.rosenberger.com/en/downloads/mdm.php. Serial number on both sides of cable ends for network documentation, Product ID label on each packaging, including installation manual available in any standard length. Benefits Cost reduction through direct attach of the IT Hardware Transceivers to the TMJ connector legs Most cost-effective solution for trunks up to 24 fibers and short lengths Attenuation reduction through the saving of one connection in the transmission channel Application specific individually configurable Fast and safe installation trough factory assembled Plug & Play systematic Highest quality and cost-efficiency through factory assembling PreCONNECT® cabling systems consist of perfectly harmonized modular single components.

PreCONNECT® TRUNK MULTIJUMPERApplicationsCabling of large switches and floor-standing IT hardware within data centers, to represent their ports in a patch location.Trunk Multijumper up to 144 fibers per trunkCost and attenuation optimizedFocused on a practical and necessary approachMore information about the different applications can be found in the separates product information.PropertiesPreCONNECT® MULTIJUMPER Trunk cable:Cable ends are molded in distribution heads and assembled with „variable“ long or "stepped" connector legs.The PreCONNECT® cable divider is a mechanically and thermally robust and splice-less cable divider for fiber separation of loose tube cables. With its integrated PreCONNECT® square interface, the cable divider can be tool-less hooked into PreCONNECT® panels for tensile and torsion resistant fixing of the trunk cables.Installation protection:The connector legs and cable dividers are packed in with a non pull resistant dustproof foil tube. Stepped connector legs can be packed optionally in 600 N tensile strength, crush resistant, kink and torsion resistant, installation tubes.Connector types:According to IEC 61754-x, for more connector specifications see data sheet.SC: IEC 61754-4MTP®: IEC 61754-7E2000®: IEC 61754-15LC: IEC 61754-20Polarity:The connector legs are alphanumerically uniquely coded. The standard polarity is „channel-wise crossed“ (pairwise flipped) for full-duplex transmission systems – A1 to B1, A2 to B2, etc. On request „uncrossed“ deliverable.Fiber types:According to ISO/IEC 11801, EN 50173-1, IEC 60793-2-x and ITUG65x, for more fiber specifications see data sheet.OM3: IEC 60793-2-10 type A1a.2, ITU G.651.1OM4: IEC 60793-2-10 type A1a.3, ITU G.651.1OM5: IEC 60793-2-10 type A1a.4, ITU G.651.1OS2: IEC 60793-2-50 type B1.3, ITU G.657.A1Cable type:FRNC-LSZH cable, for more cable specifications see data sheet.Length definition:Order-length = length between the connectors of the longest legs at both sides, not between the PreCONNECT® cable dividers.Scope of delivery and packaging:Dependent on the length as cable ring or on cardboard or wooden drum, 100% IL factory measured with measurement protocol, measurement values on request or via our website: https://www.rosenberger.com/en/downloads/mdm.php. Serial number on both sides of cable ends for network documentation, Product ID label on each packaging, including installation manual available in any standard length.BenefitsCost reduction through direct attach of the IT Hardware Transceivers to the TMJ connector legsMost cost-effective solution for trunks up to 24 fibers and short lengthsAttenuation reduction through the saving of one connection in the transmission channelApplication specific individually configurableFast and safe installation trough factory assembled Plug & Play systematicHighest quality and cost-efficiency through factory assemblingPreCONNECT® cabling systems consist of perfectly harmonized modular single components.

PreCONNECT® TRUNK MULTIJUMPERApplicationsCabling of large switches and floor-standing IT hardware within data centers, to represent their ports in a patch location.Trunk Multijumper up to 144 fibers per trunkCost and attenuation optimizedFocused on a practical and necessary approachMore information about the different applications can be found in the separates product information.PropertiesPreCONNECT® MULTIJUMPER Trunk cable:Cable ends are molded in distribution heads and assembled with „variable“ long or "stepped" connector legs.The PreCONNECT® cable divider is a mechanically and thermally robust and splice-less cable divider for fiber separation of loose tube cables. With its integrated PreCONNECT® square interface, the cable divider can be tool-less hooked into PreCONNECT® panels for tensile and torsion resistant fixing of the trunk cables.Installation protection:The connector legs and cable dividers are packed in with a non pull resistant dustproof foil tube. Stepped connector legs can be packed optionally in 600 N tensile strength, crush resistant, kink and torsion resistant, installation tubes.Connector types:According to IEC 61754-x, for more connector specifications see data sheet.SC: IEC 61754-4MTP®: IEC 61754-7E2000®: IEC 61754-15LC: IEC 61754-20Polarity:The connector legs are alphanumerically uniquely coded. The standard polarity is „channel-wise crossed“ (pairwise flipped) for full-duplex transmission systems – A1 to B1, A2 to B2, etc. On request „uncrossed“ deliverable.Fiber types:According to ISO/IEC 11801, EN 50173-1, IEC 60793-2-x and ITUG65x, for more fiber specifications see data sheet.OM3: IEC 60793-2-10 type A1a.2, ITU G.651.1OM4: IEC 60793-2-10 type A1a.3, ITU G.651.1OM5: IEC 60793-2-10 type A1a.4, ITU G.651.1OS2: IEC 60793-2-50 type B1.3, ITU G.657.A1Cable type:FRNC-LSZH cable, for more cable specifications see data sheet.Length definition:Order-length = length between the connectors of the longest legs at both sides, not between the PreCONNECT® cable dividers.Scope of delivery and packaging:Dependent on the length as cable ring or on cardboard or wooden drum, 100% IL factory measured with measurement protocol, measurement values on request or via our website: https://www.rosenberger.com/en/downloads/mdm.php. Serial number on both sides of cable ends for network documentation, Product ID label on each packaging, including installation manual available in any standard length.BenefitsCost reduction through direct attach of the IT Hardware Transceivers to the TMJ connector legsMost cost-effective solution for trunks up to 24 fibers and short lengthsAttenuation reduction through the saving of one connection in the transmission channelApplication specific individually configurableFast and safe installation trough factory assembled Plug & Play systematicHighest quality and cost-efficiency through factory assemblingPreCONNECT® cabling systems consist of perfectly harmonized modular single components.

PreCONNECT® TRUNK MULTIJUMPERApplicationsCabling of large switches and floor-standing IT hardware within data centers, to represent their ports in a patch location.Trunk Multijumper up to 144 fibers per trunkCost and attenuation optimizedFocused on a practical and necessary approachMore information about the different applications can be found in the separates product information.PropertiesPreCONNECT® MULTIJUMPER Trunk cable:Cable ends are molded in distribution heads and assembled with „variable“ long or "stepped" connector legs.The PreCONNECT® cable divider is a mechanically and thermally robust and splice-less cable divider for fiber separation of loose tube cables. With its integrated PreCONNECT® square interface, the cable divider can be tool-less hooked into PreCONNECT® panels for tensile and torsion resistant fixing of the trunk cables.Installation protection:The connector legs and cable dividers are packed in with a non pull resistant dustproof foil tube. Stepped connector legs can be packed optionally in 600 N tensile strength, crush resistant, kink and torsion resistant, installation tubes.Connector types:According to IEC 61754-x, for more connector specifications see data sheet.SC: IEC 61754-4MTP®: IEC 61754-7E2000®: IEC 61754-15LC: IEC 61754-20Polarity:The connector legs are alphanumerically uniquely coded. The standard polarity is „channel-wise crossed“ (pairwise flipped) for full-duplex transmission systems – A1 to B1, A2 to B2, etc. On request „uncrossed“ deliverable.Fiber types:According to ISO/IEC 11801, EN 50173-1, IEC 60793-2-x and ITUG65x, for more fiber specifications see data sheet.OM3: IEC 60793-2-10 type A1a.2, ITU G.651.1OM4: IEC 60793-2-10 type A1a.3, ITU G.651.1OM5: IEC 60793-2-10 type A1a.4, ITU G.651.1OS2: IEC 60793-2-50 type B1.3, ITU G.657.A1Cable type:FRNC-LSZH cable, for more cable specifications see data sheet.Length definition:Order-length = length between the connectors of the longest legs at both sides, not between the PreCONNECT® cable dividers.Scope of delivery and packaging:Dependent on the length as cable ring or on cardboard or wooden drum, 100% IL factory measured with measurement protocol, measurement values on request or via our website: https://www.rosenberger.com/en/downloads/mdm.php. Serial number on both sides of cable ends for network documentation, Product ID label on each packaging, including installation manual available in any standard length.BenefitsCost reduction through direct attach of the IT Hardware Transceivers to the TMJ connector legsMost cost-effective solution for trunks up to 24 fibers and short lengthsAttenuation reduction through the saving of one connection in the transmission channelApplication specific individually configurableFast and safe installation trough factory assembled Plug & Play systematicHighest quality and cost-efficiency through factory assemblingPreCONNECT® cabling systems consist of perfectly harmonized modular single components.

PreCONNECT® TRUNK MULTIJUMPERApplicationsCabling of large switches and floor-standing IT hardware within data centers, to represent their ports in a patch location.Trunk Multijumper up to 144 fibers per trunkCost and attenuation optimizedFocused on a practical and necessary approachMore information about the different applications can be found in the separates product information.PropertiesPreCONNECT® MULTIJUMPER Trunk cable:Cable ends are molded in distribution heads and assembled with „variable“ long or "stepped" connector legs.The PreCONNECT® cable divider is a mechanically and thermally robust and splice-less cable divider for fiber separation of loose tube cables. With its integrated PreCONNECT® square interface, the cable divider can be tool-less hooked into PreCONNECT® panels for tensile and torsion resistant fixing of the trunk cables.Installation protection:The connector legs and cable dividers are packed in with a non pull resistant dustproof foil tube. Stepped connector legs can be packed optionally in 600 N tensile strength, crush resistant, kink and torsion resistant, installation tubes.Connector types:According to IEC 61754-x, for more connector specifications see data sheet.SC: IEC 61754-4MTP®: IEC 61754-7E2000®: IEC 61754-15LC: IEC 61754-20Polarity:The connector legs are alphanumerically uniquely coded. The standard polarity is „channel-wise crossed“ (pairwise flipped) for full-duplex transmission systems – A1 to B1, A2 to B2, etc. On request „uncrossed“ deliverable.Fiber types:According to ISO/IEC 11801, EN 50173-1, IEC 60793-2-x and ITUG65x, for more fiber specifications see data sheet.OM3: IEC 60793-2-10 type A1a.2, ITU G.651.1OM4: IEC 60793-2-10 type A1a.3, ITU G.651.1OM5: IEC 60793-2-10 type A1a.4, ITU G.651.1OS2: IEC 60793-2-50 type B1.3, ITU G.657.A1Cable type:FRNC-LSZH cable, for more cable specifications see data sheet.Length definition:Order-length = length between the connectors of the longest legs at both sides, not between the PreCONNECT® cable dividers.Scope of delivery and packaging:Dependent on the length as cable ring or on cardboard or wooden drum, 100% IL factory measured with measurement protocol, measurement values on request or via our website: https://www.rosenberger.com/en/downloads/mdm.php. Serial number on both sides of cable ends for network documentation, Product ID label on each packaging, including installation manual available in any standard length.BenefitsCost reduction through direct attach of the IT Hardware Transceivers to the TMJ connector legsMost cost-effective solution for trunks up to 24 fibers and short lengthsAttenuation reduction through the saving of one connection in the transmission channelApplication specific individually configurableFast and safe installation trough factory assembled Plug & Play systematicHighest quality and cost-efficiency through factory assemblingPreCONNECT® cabling systems consist of perfectly harmonized modular single components.

PreCONNECT® TRUNK MULTIJUMPERApplicationsCabling of large switches and floor-standing IT hardware within data centers, to represent their ports in a patch location.Trunk Multijumper up to 144 fibers per trunkCost and attenuation optimizedFocused on a practical and necessary approachMore information about the different applications can be found in the separates product information.PropertiesPreCONNECT® MULTIJUMPER Trunk cable:Cable ends are molded in distribution heads and assembled with „variable“ long or "stepped" connector legs.The PreCONNECT® cable divider is a mechanically and thermally robust and splice-less cable divider for fiber separation of loose tube cables. With its integrated PreCONNECT® square interface, the cable divider can be tool-less hooked into PreCONNECT® panels for tensile and torsion resistant fixing of the trunk cables.Installation protection:The connector legs and cable dividers are packed in with a non pull resistant dustproof foil tube. Stepped connector legs can be packed optionally in 600 N tensile strength, crush resistant, kink and torsion resistant, installation tubes.Connector types:According to IEC 61754-x, for more connector specifications see data sheet.SC: IEC 61754-4MTP®: IEC 61754-7E2000®: IEC 61754-15LC: IEC 61754-20Polarity:The connector legs are alphanumerically uniquely coded. The standard polarity is „channel-wise crossed“ (pairwise flipped) for full-duplex transmission systems – A1 to B1, A2 to B2, etc. On request „uncrossed“ deliverable.Fiber types:According to ISO/IEC 11801, EN 50173-1, IEC 60793-2-x and ITUG65x, for more fiber specifications see data sheet.OM3: IEC 60793-2-10 type A1a.2, ITU G.651.1OM4: IEC 60793-2-10 type A1a.3, ITU G.651.1OM5: IEC 60793-2-10 type A1a.4, ITU G.651.1OS2: IEC 60793-2-50 type B1.3, ITU G.657.A1Cable type:FRNC-LSZH cable, for more cable specifications see data sheet.Length definition:Order-length = length between the connectors of the longest legs at both sides, not between the PreCONNECT® cable dividers.Scope of delivery and packaging:Dependent on the length as cable ring or on cardboard or wooden drum, 100% IL factory measured with measurement protocol, measurement values on request or via our website: https://www.rosenberger.com/en/downloads/mdm.php. Serial number on both sides of cable ends for network documentation, Product ID label on each packaging, including installation manual available in any standard length.BenefitsCost reduction through direct attach of the IT Hardware Transceivers to the TMJ connector legsMost cost-effective solution for trunks up to 24 fibers and short lengthsAttenuation reduction through the saving of one connection in the transmission channelApplication specific individually configurableFast and safe installation trough factory assembled Plug & Play systematicHighest quality and cost-efficiency through factory assemblingPreCONNECT® cabling systems consist of perfectly harmonized modular single components.

PreCONNECT® TRUNK MULTIJUMPERApplicationsCabling of large switches and floor-standing IT hardware within data centers, to represent their ports in a patch location.Trunk Multijumper up to 144 fibers per trunkCost and attenuation optimizedFocused on a practical and necessary approachMore information about the different applications can be found in the separates product information.PropertiesPreCONNECT® MULTIJUMPER Trunk cable:Cable ends are molded in distribution heads and assembled with „variable“ long or "stepped" connector legs.The PreCONNECT® cable divider is a mechanically and thermally robust and splice-less cable divider for fiber separation of loose tube cables. With its integrated PreCONNECT® square interface, the cable divider can be tool-less hooked into PreCONNECT® panels for tensile and torsion resistant fixing of the trunk cables.Installation protection:The connector legs and cable dividers are packed in with a non pull resistant dustproof foil tube. Stepped connector legs can be packed optionally in 600 N tensile strength, crush resistant, kink and torsion resistant, installation tubes.Connector types:According to IEC 61754-x, for more connector specifications see data sheet.SC: IEC 61754-4MTP®: IEC 61754-7E2000®: IEC 61754-15LC: IEC 61754-20Polarity:The connector legs are alphanumerically uniquely coded. The standard polarity is „channel-wise crossed“ (pairwise flipped) for full-duplex transmission systems – A1 to B1, A2 to B2, etc. On request „uncrossed“ deliverable.Fiber types:According to ISO/IEC 11801, EN 50173-1, IEC 60793-2-x and ITUG65x, for more fiber specifications see data sheet.OM3: IEC 60793-2-10 type A1a.2, ITU G.651.1OM4: IEC 60793-2-10 type A1a.3, ITU G.651.1OM5: IEC 60793-2-10 type A1a.4, ITU G.651.1OS2: IEC 60793-2-50 type B1.3, ITU G.657.A1Cable type:FRNC-LSZH cable, for more cable specifications see data sheet.Length definition:Order-length = length between the connectors of the longest legs at both sides, not between the PreCONNECT® cable dividers.Scope of delivery and packaging:Dependent on the length as cable ring or on cardboard or wooden drum, 100% IL factory measured with measurement protocol, measurement values on request or via our website: https://www.rosenberger.com/en/downloads/mdm.php. Serial number on both sides of cable ends for network documentation, Product ID label on each packaging, including installation manual available in any standard length.BenefitsCost reduction through direct attach of the IT Hardware Transceivers to the TMJ connector legsMost cost-effective solution for trunks up to 24 fibers and short lengthsAttenuation reduction through the saving of one connection in the transmission channelApplication specific individually configurableFast and safe installation trough factory assembled Plug & Play systematicHighest quality and cost-efficiency through factory assemblingPreCONNECT® cabling systems consist of perfectly harmonized modular single components.

PreCONNECT® TRUNK MULTIJUMPERApplicationsCabling of large switches and floor-standing IT hardware within data centers, to represent their ports in a patch location.Trunk Multijumper up to 144 fibers per trunkCost and attenuation optimizedFocused on a practical and necessary approachMore information about the different applications can be found in the separates product information.PropertiesPreCONNECT® MULTIJUMPER Trunk cable:Cable ends are molded in distribution heads and assembled with „variable“ long or "stepped" connector legs.The PreCONNECT® cable divider is a mechanically and thermally robust and splice-less cable divider for fiber separation of loose tube cables. With its integrated PreCONNECT® square interface, the cable divider can be tool-less hooked into PreCONNECT® panels for tensile and torsion resistant fixing of the trunk cables.Installation protection:The connector legs and cable dividers are packed in with a non pull resistant dustproof foil tube. Stepped connector legs can be packed optionally in 600 N tensile strength, crush resistant, kink and torsion resistant, installation tubes.Connector types:According to IEC 61754-x, for more connector specifications see data sheet.SC: IEC 61754-4MTP®: IEC 61754-7E2000®: IEC 61754-15LC: IEC 61754-20Polarity:The connector legs are alphanumerically uniquely coded. The standard polarity is „channel-wise crossed“ (pairwise flipped) for full-duplex transmission systems – A1 to B1, A2 to B2, etc. On request „uncrossed“ deliverable.Fiber types:According to ISO/IEC 11801, EN 50173-1, IEC 60793-2-x and ITUG65x, for more fiber specifications see data sheet.OM3: IEC 60793-2-10 type A1a.2, ITU G.651.1OM4: IEC 60793-2-10 type A1a.3, ITU G.651.1OM5: IEC 60793-2-10 type A1a.4, ITU G.651.1OS2: IEC 60793-2-50 type B1.3, ITU G.657.A1Cable type:FRNC-LSZH cable, for more cable specifications see data sheet.Length definition:Order-length = length between the connectors of the longest legs at both sides, not between the PreCONNECT® cable dividers.Scope of delivery and packaging:Dependent on the length as cable ring or on cardboard or wooden drum, 100% IL factory measured with measurement protocol, measurement values on request or via our website: https://www.rosenberger.com/en/downloads/mdm.php. Serial number on both sides of cable ends for network documentation, Product ID label on each packaging, including installation manual available in any standard length.BenefitsCost reduction through direct attach of the IT Hardware Transceivers to the TMJ connector legsMost cost-effective solution for trunks up to 24 fibers and short lengthsAttenuation reduction through the saving of one connection in the transmission channelApplication specific individually configurableFast and safe installation trough factory assembled Plug & Play systematicHighest quality and cost-efficiency through factory assemblingPreCONNECT® cabling systems consist of perfectly harmonized modular single components.

PreCONNECT® TRUNK MULTIJUMPERApplicationsCabling of large switches and floor-standing IT hardware within data centers, to represent their ports in a patch location.Trunk Multijumper up to 144 fibers per trunkCost and attenuation optimizedFocused on a practical and necessary approachMore information about the different applications can be found in the separates product information.PropertiesPreCONNECT® MULTIJUMPER Trunk cable:Cable ends are molded in distribution heads and assembled with „variable“ long or "stepped" connector legs.The PreCONNECT® cable divider is a mechanically and thermally robust and splice-less cable divider for fiber separation of loose tube cables. With its integrated PreCONNECT® square interface, the cable divider can be tool-less hooked into PreCONNECT® panels for tensile and torsion resistant fixing of the trunk cables.Installation protection:The connector legs and cable dividers are packed in with a non pull resistant dustproof foil tube. Stepped connector legs can be packed optionally in 600 N tensile strength, crush resistant, kink and torsion resistant, installation tubes.Connector types:According to IEC 61754-x, for more connector specifications see data sheet.SC: IEC 61754-4MTP®: IEC 61754-7E2000®: IEC 61754-15LC: IEC 61754-20Polarity:The connector legs are alphanumerically uniquely coded. The standard polarity is „channel-wise crossed“ (pairwise flipped) for full-duplex transmission systems – A1 to B1, A2 to B2, etc. On request „uncrossed“ deliverable.Fiber types:According to ISO/IEC 11801, EN 50173-1, IEC 60793-2-x and ITUG65x, for more fiber specifications see data sheet.OM3: IEC 60793-2-10 type A1a.2, ITU G.651.1OM4: IEC 60793-2-10 type A1a.3, ITU G.651.1OM5: IEC 60793-2-10 type A1a.4, ITU G.651.1OS2: IEC 60793-2-50 type B1.3, ITU G.657.A1Cable type:FRNC-LSZH cable, for more cable specifications see data sheet.Length definition:Order-length = length between the connectors of the longest legs at both sides, not between the PreCONNECT® cable dividers.Scope of delivery and packaging:Dependent on the length as cable ring or on cardboard or wooden drum, 100% IL factory measured with measurement protocol, measurement values on request or via our website: https://www.rosenberger.com/en/downloads/mdm.php. Serial number on both sides of cable ends for network documentation, Product ID label on each packaging, including installation manual available in any standard length.BenefitsCost reduction through direct attach of the IT Hardware Transceivers to the TMJ connector legsMost cost-effective solution for trunks up to 24 fibers and short lengthsAttenuation reduction through the saving of one connection in the transmission channelApplication specific individually configurableFast and safe installation trough factory assembled Plug & Play systematicHighest quality and cost-efficiency through factory assemblingPreCONNECT® cabling systems consist of perfectly harmonized modular single components.